Secure Clips - SCAFCO Steel Stud Company https://www.scafco.com/steel/products/secure-clips/ Steel Framing Studs and Track Mon, 25 Nov 2024 23:39:44 +0000 en-US hourly 1 https://wordpress.org/?v=6.3.5 PHC – Panel Hoist Clip https://www.scafco.com/products/secure-clips/phc-panel-hoist-clip/ Fri, 22 Nov 2024 23:03:55 +0000 https://www.scafco.com/?page_id=6407 Part No. Panel Studs Panel Lifted from a Vertical Orientation (F3) Panel Lifted from a Horizontal Orientation (F2) PHC8 PHC12 PHC8 PHC12 Mils Fy (ksi) 3 #10 Screws 5 #10 Screws 6 #10 Screws 5 #10 Screws 8 #10 Screws 12 #10 Screws 3 #10 Screws 5 #10 Screws 6 #10 Screws 5 #10 Screws […]

The post PHC – Panel Hoist Clip appeared first on SCAFCO Steel Stud Company.

]]> The PHC panel hoist clip attaches to manufactured wall or floor panels to provided lifting points for installation on the jobsite. The hoist clip has a 1-1/2” diameter hole for attaching cables for lifting, along with prepunched holes for screw attachments to the panel.

PHC Clip

Features and Benefits

  • Provides lifting points for prefabricated panels
  • Available in 2 convenient lengths
  • Loads based on #10 screws
  • Pre-punched screw and lift holes
  • Rounded Corners for ease of hoisting
thumbnail of PHC

PHC Submittal Download

Material Composition

  • Mill certified steel
  • ASTM A653/A653M
  • 97 mil
    – 57 ksi yield strength
    – 65 ksi tensile strength
    – G60 galvanized coating
PHC Clip

Part No. Panel Studs Panel Lifted from a Vertical Orientation (F3) Panel Lifted from a Horizontal Orientation (F2)
PHC8 PHC12 PHC8 PHC12
Mils Fy (ksi) 3 #10 Screws 5 #10 Screws 6 #10 Screws 5 #10 Screws 8 #10 Screws 12 #10 Screws 3 #10 Screws 5 #10 Screws 6 #10 Screws 5 #10 Screws 8 #10 Screws 12 #10 Screws
PHC 33EQS 57 603 1005 1206 1005 1608 2412 88 201 253 118 217 478
33 33 531 885 1062 885 1416 2124 88 201 253 118 217 478
43EQS 57 951 1585 1902 1585 2536 2542 131 307 394 176 350 710
43 33 789 1315 1578 1315 2104 2542 131 307 394 176 350 710
54 50 1602 2542 2542 2542 2542 2542 269 635 783 318 701 1095
68 50 1644 2542 2542 2542 2542 2542 269 635 817 318 701 1095
97 50 1644 2542 2542 2542 2542 2542 269 635 817 318 701 1095
118 50 1644 2542 2542 2542 2542 2542 269 635 817 318 701 1095

Table notes:

  1. Loads based on AISI-S100 and the Allowable Strength Design (ASD), assuming #10 Screws for attachment to stud/panel.
  2. Allowable Loads assume the use of a load distribution member (spreader bar) between hoist points.
  3. The spacing of hoist points is to be controlled by the weight of the panel and approved by the designer.
  4. Allowable loads indicated on the table(s) are for force in a single direction only. The designer shall use the combined forces check as required by AISI S100 if more than one force is applied to the connection.
  5. The nominal strength of the screw must be at least 3.75 times the allowable load.
  6. Screw shear capacities are based on allowable strength design (ASD) and include a safety factor of 3.0.

Quantity / Order Information

Part No. Left/Right
Handed		 Qty
/Bucket		 Lbs
/Bucket
PHC8-97 8″ 60 40
PHC12-97 12″ 40 40

The post PHC – Panel Hoist Clip appeared first on SCAFCO Steel Stud Company.

]]> AC – Bypass Slab Secure Clip https://www.scafco.com/steel/products/secure-clips/ac-bypass-slab-secure-clip/ Thu, 26 Oct 2017 09:00:55 +0000 http://new.scafco.com/?page_id=110 Material Composition ASTM A653/A653M Material thickness: 68 mil Yield strength: 57 ksi G90 galvanized coating Allowable Loads Model No. Stud Properties F1 Allowable Loads (lbs) F3 Allowable Loads (lbs) Mils Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 4 #10 Screws 2 #10 Screws 3 #10 Screws 4 #10 Screws AC250 AC350 AC550 33EQS […]

The post AC – Bypass Slab Secure Clip appeared first on SCAFCO Steel Stud Company.

]]>
The bypass slab secure clip (AC) connects an exterior wall stud that bypasses the building structure through the use of a 90° angle. It is designed to resist horizontal and vertical loads, and has pre-punched guide holes in each leg for fast and easy installation. The AC may be attached to the structure with either an approved fastener or a weld, depending on the material properties of the structure and the proposed design.

AC Clip


Features

  • Pre-punched guide holes for quick attachment to structure and stud
  • Available in a variety of different lengths for all requirements and construction tolerances
  • Replaces the expensive traditional method of bracing
  • Produced from thicker steel to improve welded attachments

thumbnail of AC

AC Submittal Download


Material Composition

  • ASTM A653/A653M
  • Material thickness: 68 mil
  • Yield strength: 57 ksi
  • G90 galvanized coating

Allowable Loads

AC Clip Loads
AC Clip Loads

Model No. Stud Properties F1 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mils Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 4 #10 Screws 2 #10 Screws 3 #10 Screws 4 #10 Screws
AC250
AC350
AC550		 33EQS 20 57 402 603 804 402 603 804
33 20 33 353 530 707 353 530 707
43EQS 18 57 635 952 1269 635 952 1269
43 18 33 526 789 1052 526 789 1052
54 16 50 1068 1602 1940 1068 1602 1940
68 14 50 1510 1940 1940 1940 1940 1940
97 12 50 1585 1940 1940 1940 1940 1940
118 10 50 1585 1940 1940 1940 1940 1940
Maximum Allowable Clip Capacity Max F1 = 1940 lbs Max F3 = 1940 lbs

Model No. Stud Properties F1 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mils Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 4 #10 Screws 6 #10 Screws 8 #10 Screws
AC750 33EQS 20 57 804 1206 1608 804 1206 1608
33 20 33 707 1060 1414 707 1060 1414
43EQS 18 57 1269 1903 1940 1269 1903 1940
43 18 33 1052 1578 1940 1052 1578 1940
54 16 50 1940 1940 1940 1940 1940 1940
68 14 50 1940 1940 1940 1940 1940 1940
97 12 50 1940 1940 1940 1940 1940 1940
118 10 50 1940 1940 1940 1940 1940 1940
Maximum Allowable Clip Capacity Max F1 = 1940 lbs Max F3 = 1940 lbs

AC Clip Loads

Model No. Stud Properties F1 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mils Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 4 #10 Screws 6 #10 Screws 8 #10 Screws
AC750
(with 2″ offset)		 33EQS 20 57 804 1206 1608 804 1206 1550
33 20 33 707 1060 1414 707 1060 1414
43EQS 18 57 1269 1550 1550 1269 1550 1550
43 18 33 1052 1550 1550 1052 1550 1550
54 16 50 1550 1550 1550 1550 1550 1550
68 14 50 1550 1550 1550 1550 1550 1550
97 12 50 1550 1550 1550 1550 1550 1550
118 10 50 1550 1550 1550 1550 1550 1550
Maximum Allowable Clip Capacity Max F1 = 1550 lbs Max F3 = 1550 lbs

AC Clip Loads

Model No. Stud Properties F1 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mils Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 4 #10 Screws 6 #10 Screws 8 #10 Screws
AC950
(with 2″ offset)		 33EQS 20 57 804 1030 1030 804 1030 1030
33 20 33 707 1030 1030 707 1030 1030
43EQS 18 57 1030 1030 1030 1030 1030 1030
43 18 33 1030 1030 1030 1030 1030 1030
54 16 50 1030 1030 1030 1030 1030 1030
68 14 50 1030 1030 1030 1030 1030 1030
97 12 50 1030 1030 1030 1030 1030 1030
118 10 50 1030 1030 1030 1030 1030 1030
Maximum Allowable Clip Capacity Max F1 = 1030 lbs Max F3 = 1030 lbs

Screw shear values are based on the SSMA Screw Table with the following notes:

    1. The allowable loads are based on the steel properties of the members being connected, per NASPEC with AISI S100-07/S2-10 supplement.
    2. The nominal strength of the screw must be at least 3.75 times the allowable loads.
    3. Values include a 3.0 factor of safety.
    4. Penetration of screws through joined materials should not be less than 3 exposed threads. Screws should be installed and tightened in accordance with the screw  manufacturer’s recommendations.
    5. Allowable loads indicated on the table(s) are for force in single direction only. If more than one force is applied to the connection, the designer shall provide the combined forces check as required by NASPEC with 2004 supplements.
    6. It is the responsibility of the designer to check the bending in the short leg of this clip.
    7. Details above indicate screw locations. Not all screw locations will have pre punched holes, refer to product drawing.

Quantity / Order Information

Part No. Width Qty
/Bucket		 Lbs
/Bucket
AC250 2 ½” 50 23
AC350 3 ½” 50 29
AC550 5 ½” 50 41
AC750 7 ½” 50 52
AC950 9 ½” 35 45

Note: Additional lengths available upon request.

The post AC – Bypass Slab Secure Clip appeared first on SCAFCO Steel Stud Company.

]]> AS – Load-Bearing Secure Strut https://www.scafco.com/steel/products/secure-clips/as-load-bearing-secure-strut/ Wed, 25 Oct 2017 17:28:02 +0000 http://new.scafco.com/?page_id=415 Material Composition ASTM A653/A653M Material thickness: 68 mil Yield strength: 57 ksi G90 galvanized coating Quantity / Order Information Model No. Width Qty /Bucket Lbs /Bucket AS800 8” 50 36 AS1000 10” 50 45 AS1200 12” 50 54 AS1500 15” – – AS2000 20” – – AS2400 24” – –

The post AS – Load-Bearing Secure Strut appeared first on SCAFCO Steel Stud Company.

]]>
The load-bearing secure strut (AS) is used in various applications, but most commonly to connect an exterior wall stud that bypasses the building structure through the use of a 90° angle strut. The AS is designed to resist compression loads and axial tension. It may be attached to the structure with either an approved fastener or a weld, depending on the material properties of the structure and the proposed design.

AS Clip


Features

  • Variety of lengths available
  • Transfers horizontal load into structure
  • Maintains lateral rigidity
  • Eliminates bridging within 12″ of support connection

thumbnail of AS

AS Submittal Download


Material Composition

  • ASTM A653/A653M
  • Material thickness: 68 mil
  • Yield strength: 57 ksi
  • G90 galvanized coating

AS Clip

AS Clip

Quantity / Order Information

Model No. Width Qty
/Bucket		 Lbs
/Bucket
AS800 8” 50 36
AS1000 10” 50 45
AS1200 12” 50 54
AS1500 15” – –
AS2000 20” – –
AS2400 24” – –

The post AS – Load-Bearing Secure Strut appeared first on SCAFCO Steel Stud Company.

]]> FA – Secure Floor Anchor Clip https://www.scafco.com/steel/products/secure-clips/fa-secure-floor-anchor-clip/ Tue, 24 Oct 2017 18:08:52 +0000 http://new.scafco.com/?page_id=433 Material Composition Allowable Loads Part No. Number of Screws from Clip to Stud Stud Properties M1 Allowable Moment  (in-lbs) F1 Allowable Out-of-Plane Shear Load (lbs) F3 Max Allowable Tension Load (lbs) F3 Allowable Tension Load with 1/8” Deflection Limit (lbs) Mil Gauge Fy (ksi) FA337‑68 4 – #12 Screws 33 20 45 1692 752 1211 1141 […]

The post FA – Secure Floor Anchor Clip appeared first on SCAFCO Steel Stud Company.

]]> The secure floor anchor clip (FA) connects a wall stud to the floor and provides a secure connection through the use of a 90° angle that is designed to resist torsional, horizontal, and vertical loads. It is provided in 68 mil or 118 mil thickness to meet any design criteria and comes with pre-punched guide holes in each leg for superior installation efficiency. The FA may be attached to the structure with either an approved fastener or a weld, depending on the material properties of the structure and the proposed design.

FA Clip

Features

  • Available in 68 mil and 118 mil
  • Variety of lengths available
  • Pre-punched guide holes
  • Optional plate washer for heavy duty applications
thumbnail of FA
FA Submittal Download

Material Composition

  • ASTM A653/A653M
  • Material thickness: 68, 118 mil
  • Yield strength: 57 ksi
  • Main flange and outer guide holes: 0.1600″ diameter (#10 fasteners)
  • Inner guide holes: 0.30″ diameter (1/4″ screw anchor)
  • Center guide hole: 0.5625″ diameter (1/2″ anchor)

Allowable Loads

Part No. Number of Screws from Clip to Stud Stud Properties M1 Allowable Moment
 (in-lbs) 		F1 Allowable Out-of-Plane Shear Load (lbs) F3 Max Allowable Tension Load
(lbs) 		F3 Allowable Tension Load with 1/8” Deflection Limit (lbs)
Mil Gauge Fy (ksi)
FA337‑68 4 – #12 Screws 33 20 45 1692 752 1211 1141
43 18 45 2520 1120 1578 1141
54 16 65 5121 2276 2861 1141
68 14 65 5121 2461 3221 1141
97 12 65 5121 2461 3221 1141
FA550‑68 5 – #12 Screws 33 20 45 2272 940 1514 1514
43 18 45 3383 1400 1973 1860
54 16 65 6875 2845 3576 1860
68 14 65 9388 3885 4026 1860
97 12 65 9388 3885 4026 1860
FA750‑68 5 – #12 Screws 33 20 45 2272 940 1514 1514
43 18 45 3383 1400 1973 1973
54 16 65 6875 2845 3576 2111
68 14 65 9388 3885 4026 2111
97 12 65 9388 3885 4026 2111
FA950‑68 5 – #12 Screws 33 20 45 2272 940 1514 1514
43 18 45 3383 1400 1973 1973
54 16 65 6875 2845 3576 2338
68 14 65 9388 3885 4026 2338
97 12 65 9388 3885 4026 2338
FA1150‑68 5 – #12 Screws 33 20 45 2272 940 1514 1514
43 18 45 3383 1400 1973 1973
54 16 65 6875 2845 3576 2546
68 14 65 9388 3885 4026 2546
97 12 65 9388 3885 4026 2546
FA337‑118 4 – #12 Screws 33 20 45 1692 752 1211 1211
43 18 45 2520 1120 1578 1578
54 16 65 5121 2276 2861 2861
68 14 65 5121 3108 3604 3604
97 12 65 5121 3108 5140 5140
FA550‑118
FA750‑118
FA950‑118
FA1150‑118		 5 – #12 Screws 33 20 45 2272 940 1514 1514
43 18 45 3383 1400 1973 1973
54 16 65 6875 2845 3576 3576
68 14 65 10885 4505 4505 4505
97 12 65 10885 6426 6426 6426

Table Notes:

  1. Loads based on AISI‐S100 and the Allowable Strength Design (ASD), assuming #12 Screws for attachment to stud.
  2. Stud Member and Structural Anchorage designed by qualified professional.
  3. Loads assume fastener connection to stud is failure method.

Quantity / Order Information

Model No. Material Thickness Width Qty
/Bucket		 Lbs
/Bucket
Width Gauge
FA337-68 68 14 3 ⅜” 100 31
FA550-68 68 14 5 ½” 50 26
FA750-68 68 14 7 ½” 50 35
FA950-68 68 14 9 ½” 50 44
FA1150-68 68 14 11 ½” 50 53
FA337-118 118 10 3 ⅜” 50 29
FA550-118 118 10 5 ½” 50 47
FA750-118 118 10 7 ½” 35 45
FA950-118 118 10 9 ½” 25 41
FA1150-118 118 10 11 ½” 25 50

The post FA – Secure Floor Anchor Clip appeared first on SCAFCO Steel Stud Company.

]]> MA – Multi-Use Secure Clip https://www.scafco.com/steel/products/secure-clips/ma-multi-use-secure-clip/ Mon, 23 Oct 2017 18:41:06 +0000 http://new.scafco.com/?page_id=439 Allowable Loads Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs) Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws MA350 33EQS 20 57 402 603 206 310 206 310 33 20 33 353 530 […]

The post MA – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]>
The multi-use secure clip (MA) is used in a variety of different applications, including head-of-wall, joist connections, securing hips, rafters and trusses, reinforcing header connections, bridging, etc. It is produced from mill certified 57 ksi steel and is designed to resist vertical and lateral loads. Pre-punched guide holes are provided in each leg for superior installation efficiency.


Features

  • Variety of lengths available
  • Loads based on #10 screws
  • Pre-punched guide holes
  • No labor used cutting scrap or angle

thumbnail of MA

MA Submittal Download


Material Composition

  • Mill certified steel
  • ASTM A653/A653M
  • 54 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G60 galvanized coating
  • 68 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G90 galvanized coating

Allowable Loads

Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws
MA350 33EQS 20 57 402 603 206 310 206 310
33 20 33 353 530 168 251 168 251
43EQS 18 57 635 952 280 420 280 420
43 18 33 526 789 219 328 219 328
54 16 50 1068 1602 396 594 396 594
68 14 50 1510 2266 499 749 499 749
97 12 50 2261 2420 712 965 712 965
Maximum Allowable Clip Capacity Max F1 = 2420 lbs Max F2 = 965 lbs Max F3 = 965 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws
MA550 33EQS 20 57 402 804 1005 206 413 516 206 413 516
33 20 33 353 707 884 168 335 419 168 335 419
43EQS 18 57 635 1269 1587 280 560 700 280 560 700
43 18 33 526 1052 1315 219 437 547 219 437 547
54 16 50 1068 2136 2671 396 792 855 396 792 855
68 14 50 1510 2980 2980 499 855 855 499 855 855
97 12 50 2261 2980 2980 712 855 855 712 855 855
Maximum Allowable Clip Capacity Max F1 = 2980 lbs Max F2 = 855 lbs Max F3 = 855 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws
MA750 33EQS 20 57 402 804 1407 206 413 722 206 413 722
33 20 33 353 707 1237 168 335 597 168 335 597
43EQS 18 57 635 1269 2221 280 560 980 280 560 980
43 18 33 526 1052 1841 219 437 765 219 437 765
54 16 50 1068 2136 3739 396 792 1387 396 792 1387
68 14 50 1510 3021 5286 499 998 1740 499 998 1740
97 12 50 2261 4521 6100 712 1424 1740 712 1424 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 5 #10 Screws 9 #10 Screws 2 #10 Screws 5#10 Screws 9 #10 Screws 2 #10 Screws 5 #10 Screws 9 #10 Screws
MA950 33EQS 20 57 402 1005 1809 206 516 929 206 516 929
33 20 33 353 884 1590 168 419 754 168 419 754
43EQS 18 57 635 1587 2856 280 700 1260 280 700 1260
43 18 33 526 1315 2367 219 547 984 219 547 984
54 16 50 1068 2671 4807 396 991 1740 396 991 1740
68 14 50 1510 3776 6100 499 1248 1740 499 1248 1740
97 12 50 2261 5652 6100 712 1740 1740 712 1740 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs

Screw shear values are based on the SSMA Screw Table with the following notes:

  1. Allowable loads have not been increased for wind, seismic activity, or other factors.
  2. The allowable loads are based on the steel properties of the members being connected, per AISI S100.
  3. The nominal strength of the screw must be at least 3.75 times the allowable loads.
  4. Values include a 3.0 factor of safety.
  5. Penetration of screws through joined materials should not be less than three exposed threads. Install and tighten screws in accordance with the screw manufacturer’s recommendations.
  6. Allowable loads indicated on the table(s) are for force in single direction only. The designer shall use the combined forces check as required by AISI S100 if more than one force is applied to the connection.

Quantity / Order Information

Part No. Length Qty / Bucket Lbs / Bucket
MA350-54 3 ½” 200 34
MA350-68 3 ½” 200 42
MA550-54 5 ½” 100 26
MA550-68 5 ½” 100 32
MA750-54 7 ½” 100 35
MA750-68 7 ½” 100 44
MA950-54 9 ½” 100 44
MA950-68 9 ½” 100 55

The post MA – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]> MB – Multi-Use Secure Clip https://www.scafco.com/steel/products/secure-clips/mb-multi-use-secure-clip/ Sun, 22 Oct 2017 18:54:38 +0000 http://new.scafco.com/?page_id=445 Allowable Loads Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs) Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws MB350 33EQS 20 57 402 603 206 310 206 310 33 20 33 353 530 […]

The post MB – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]>
The multi-use secure clip (MB) is used in a variety of different applications including head-of-wall, joist connections, securing hips, rafters and trusses, reinforcing header connections, bridging, etc. It is constructed with mill certified 57 ksi steel designed to resist vertical and lateral loads. Pre-punched guide holes are provided in each leg for superior installation efficiency.


Features

  • Variety of lengths available
  • Loads based on #10 screws
  • Pre-punched guide holes
  • No labor used cutting scrap or angle

thumbnail of MB

MB Submittal Download


Material Composition

  • Mill certified steel
  • ASTM A653/A653M
  • 54 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G60 galvanized coating
  • 68 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G90 galvanized coating

Allowable Loads

Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws
MB350 33EQS 20 57 402 603 206 310 206 310
33 20 33 353 530 168 251 168 251
43EQS 18 57 635 952 280 420 280 420
43 18 33 526 789 219 328 219 328
54 16 50 1068 1602 396 594 396 594
68 14 50 1510 2266 499 749 499 749
97 12 50 2261 2420 712 965 712 965
Maximum Allowable Clip Capacity Max F1 = 2420 lbs Max F2 = 965 lbs Max F3 = 965 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws
MB550 33EQS 20 57 402 804 1005 206 413 516 206 413 516
33 20 33 353 707 884 168 335 419 168 335 419
43EQS 18 57 635 1269 1587 280 560 700 280 560 700
43 18 33 526 1052 1315 219 437 547 219 437 547
54 16 50 1068 2136 2671 396 792 855 396 792 855
68 14 50 1510 2980 2980 499 855 855 499 855 855
97 12 50 2261 2980 2980 712 855 855 712 855 855
Maximum Allowable Clip Capacity Max F1 = 2980 lbs Max F2 = 855 lbs Max F3 = 855 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws
MB750 33EQS 20 57 402 804 1407 206 413 722 206 413 722
33 20 33 353 707 1237 168 335 597 168 335 597
43EQS 18 57 635 1269 2221 280 560 980 280 560 980
43 18 33 526 1052 1841 219 437 765 219 437 765
54 16 50 1068 2136 3739 396 792 1387 396 792 1387
68 14 50 1510 3021 5286 499 998 1740 499 998 1740
97 12 50 2261 4521 6100 712 1424 1740 712 1424 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 5 #10 Screws 9 #10 Screws 2 #10 Screws 5#10 Screws 9 #10 Screws 2 #10 Screws 5 #10 Screws 9 #10 Screws
MB950 33EQS 20 57 402 1005 1809 206 516 929 206 516 929
33 20 33 353 884 1590 168 419 754 168 419 754
43EQS 18 57 635 1587 2856 280 700 1260 280 700 1260
43 18 33 526 1315 2367 219 547 984 219 547 984
54 16 50 1068 2671 4807 396 991 1740 396 991 1740
68 14 50 1510 3776 6100 499 1248 1740 499 1248 1740
97 12 50 2261 5652 6100 712 1740 1740 712 1740 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs

Screw shear values are based on the SSMA Screw Table with the following notes:

  1. Allowable loads have not been increased for wind, seismic activity, or other factors.
  2. The allowable loads are based on the steel properties of the members being connected, per AISI S100.
  3. The nominal strength of the screw must be at least 3.75 times the allowable loads.
  4. Values include a 3.0 factor of safety.
  5. Penetration of screws through joined materials should not be less than three exposed threads. Install and tighten screws in accordance with the screw manufacturer’s recommendations.
  6. Allowable loads indicated on the table(s) are for force in single direction only. The designer shall use the combined forces check as required by AISI S100 if more than one force is applied to the connection.

Quantity / Order Information

Part No. Length Qty / Bucket Lbs / Bucket
MB350-54 3 ½” 100 25
MB350-68 3 ½” 100 31
MB550-54 5 ½” 100 38
MB550-68 5 ½” 100 48
MB750-54 7 ½” 75 39
MB750-68 7 ½” 75 49
MB950-54 9 ½” 50 33
MB950-68 9 ½” 50 42

The post MB – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]> MC – Multi-Use Secure Clip https://www.scafco.com/steel/products/secure-clips/mc-multi-use-secure-clip/ Sat, 21 Oct 2017 20:14:29 +0000 http://new.scafco.com/?page_id=453 Allowable Loads Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs) Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws MC350 33EQS 20 57 402 603 206 310 206 310 33 20 33 353 530 […]

The post MC – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]>
The multi-use secure clip (MC) is used in a variety of different applications, including head of wall, joist connections, securing hips, rafters and trusses, reinforcing header connections, etc. Multi-use secure clip (MC) is constructed with Mill-Certified 50 ksi steel designed to resist vertical and lateral loads. Pre-punched guide holes are provided in each leg, allowing for superior installation efficiency.



Features

  • Variety of lengths available
  • Loads based on #10 screws
  • Pre-punched guide holes
  • No labor used cutting scrap or angle

thumbnail of MC

MC Submittal Download


Material Composition

  • Mill certified steel
  • ASTM A653/A653M
  • 54 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G60 galvanized coating
  • 68 mil
    • 57 ksi yield strength
    • 65 ksi tensile strength
    • G90 galvanized coating

Allowable Loads

Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws 2 #10 Screws 3 #10 Screws
MC350 33EQS 20 57 402 603 206 310 206 310
33 20 33 353 530 168 251 168 251
43EQS 18 57 635 952 280 420 280 420
43 18 33 526 789 219 328 219 328
54 16 50 1068 1602 396 594 396 594
68 14 50 1510 2266 499 749 499 749
97 12 50 2261 2420 712 965 712 965
Maximum Allowable Clip Capacity Max F1 = 2420 lbs Max F2 = 965 lbs Max F3 = 965 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws 2 #10 Screws 4 #10 Screws 5 #10 Screws
MC550 33EQS 20 57 402 804 1005 206 413 516 206 413 516
33 20 33 353 707 884 168 335 419 168 335 419
43EQS 18 57 635 1269 1587 280 560 700 280 560 700
43 18 33 526 1052 1315 219 437 547 219 437 547
54 16 50 1068 2136 2671 396 792 855 396 792 855
68 14 50 1510 2980 2980 499 855 855 499 855 855
97 12 50 2261 2980 2980 712 855 855 712 855 855
Maximum Allowable Clip Capacity Max F1 = 2980 lbs Max F2 = 855 lbs Max F3 = 855 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws 2 #10 Screws 4 #10 Screws 7 #10 Screws
MC750 33EQS 20 57 402 804 1407 206 413 722 206 413 722
33 20 33 353 707 1237 168 335 597 168 335 597
43EQS 18 57 635 1269 2221 280 560 980 280 560 980
43 18 33 526 1052 1841 219 437 765 219 437 765
54 16 50 1068 2136 3739 396 792 1387 396 792 1387
68 14 50 1510 3021 5286 499 998 1740 499 998 1740
97 12 50 2261 4521 6100 712 1424 1740 712 1424 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs
Part No. Stud Properties F1 Allowable Loads (lbs) F2 Allowable Loads (lbs) F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 2 #10 Screws 5 #10 Screws 9 #10 Screws 2 #10 Screws 5#10 Screws 9 #10 Screws 2 #10 Screws 5 #10 Screws 9 #10 Screws
MC950 33EQS 20 57 402 1005 1809 206 516 929 206 516 929
33 20 33 353 884 1590 168 419 754 168 419 754
43EQS 18 57 635 1587 2856 280 700 1260 280 700 1260
43 18 33 526 1315 2367 219 547 984 219 547 984
54 16 50 1068 2671 4807 396 991 1740 396 991 1740
68 14 50 1510 3776 6100 499 1248 1740 499 1248 1740
97 12 50 2261 5652 6100 712 1740 1740 712 1740 1740
Maximum Allowable Clip Capacity Max F1 = 6100 lbs Max F2 = 1740 lbs Max F3 = 1740 lbs

Screw shear values are based on the SSMA Screw Table with the following notes:

  1. Allowable loads have not been increased for wind, seismic activity, or other factors.
  2. The allowable loads are based on the steel properties of the members being connected, per AISI S100.
  3. The nominal strength of the screw must be at least 3.75 times the allowable loads.
  4. Values include a 3.0 factor of safety.
  5. Penetration of screws through joined materials should not be less than three exposed threads. Install and tighten screws in accordance with the screw manufacturer’s recommendations.
  6. Allowable loads indicated on the table(s) are for force in single direction only. The designer shall use the combined forces check as required by AISI S100 if more than one force is applied to the connection.

Quantity / Order Information

Part No. Length Qty / Bucket Lbs / Bucket
MC350-54 3 ½” 100 33
MC350-68 3 ½” 100 41
MC550-54 5 ½” 100 51
MC550-68 5 ½” 75 48
MC750-54 7 ½” 50 35
MC750-68 7 ½” 50 44
MC950-54 9 ½” 50 44
MC950-68 9 ½” 50 55

The post MC – Multi-Use Secure Clip appeared first on SCAFCO Steel Stud Company.

]]> BC – Secure Bridge Clip https://www.scafco.com/steel/products/secure-clips/bc-secure-bridge-clip/ Thu, 19 Oct 2017 20:49:54 +0000 http://new.scafco.com/?page_id=467 Allowable Loads Part No. Clip Properties (2) #10 Screws Mils Gauge Fy (ksi) F2(lbs) M1(lbs-in) BC237 33 20 33 266 155 BC337 33 20 33 532 332 BC575 54 16 50 1068 1573 BC775 54 16 50 1068 2313 Screw shear values are based on the SSMA Screw Table with the following notes: Allowable loads […]

The post BC – Secure Bridge Clip appeared first on SCAFCO Steel Stud Company.

]]>
The secure clip (BC) secures the CRC (Cold Rolled Channel) to the stud, resisting lateral movement and twisting of studs in a wall assembly. Pre-punched guide holes are provided in a specific layout accommodating the CRC and stud attachments for superior strength and installation efficiency.

Chamfered corners on one leg are cut for attachment needed for inside the stud cavity. Secure clips (BC) are packaged in rugged buckets for easy handling on the job site.

BC Clip


Features

  • Pre-punched guide holes
  • No welding or cutting scrap material required
  • Loads based on #10 screws
    • Screws are provided
  • Replaces the cumbersome traditional method of bracing

thumbnail of BC

BC Submittal Download


Material Composition

  • Mill certified steel
  • ASTM A653/A653M
  • 33 mil
    – 33 ksi yield strength
    – 45 ksi tensile strength
    – G60/G90 galvanized coating
  • 54 mil
    – 57 ksi yield strength
    – 65 ksi tensile strength
    – G60/G90 galvanized coating

BC Clip

Allowable Loads

Part No. Clip Properties (2) #10 Screws
Mils Gauge Fy (ksi) F2(lbs) M1(lbs-in)
BC237 33 20 33 266 155
BC337 33 20 33 532 332
BC575 54 16 50 1068 1573
BC775 54 16 50 1068 2313

Screw shear values are based on the SSMA Screw Table with the following notes:

  1. Allowable loads have not been increased for wind, seismic activity, or other factors.
  2. The allowable loads are based on the steel properties of the members being connected, per AISI S100.
  3. The nominal strength of the screw must be at least 3.75 times the allowable loads.
  4. Values include a 3.0 factor of safety.
  5. Penetration of screws through joined materials should not be less than three exposed threads. Install and tighten screws in accordance with the screw manufacturer’s recommendations.
  6. Allowable loads indicated on the table(s) are for force in single direction only. The designer shall use the combined forces check as required by AISI S100 if more than one force is applied to the connection.

Quantity / Order Information

Model No. Material Thickness Length Qty
/Bucket		 Lbs
/Bucket
Mils Gauge
BC237 33 20 2 ⅜” 250 17
BC337 33 20 3 ⅜” 500 48
BC575 54 16 5 ¾” 150 40
BC775 54 16 7 ¾” 100 36

The post BC – Secure Bridge Clip appeared first on SCAFCO Steel Stud Company.

]]> HG – Secure Plate Header Gusset https://www.scafco.com/steel/products/secure-clips/hg-secure-plate-header-gusset/ Tue, 17 Oct 2017 21:24:42 +0000 http://new.scafco.com/?page_id=479 Allowable Loads All screw pattern configurations depicted with jamb stud located on left hand side of clip. Part No. Stud Properties F3 Allowable Loads (lbs) Mil Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 10 #10 Screws 12 #10 Screws HG -43 (43 mil) 33EQS 20 57 804 1206 1608 2010 […]

The post HG – Secure Plate Header Gusset appeared first on SCAFCO Steel Stud Company.

]]>
SCAFCO’s secure plate header gusset (HG) is designed to provide a stiffened attachment of two individual members. Its unique design transfers the vertical load through a rigid connection that is far superior than traditional methods of construction.

The header gusset contributes to the headers web crippling and shear capacity, allowing the header to withstand larger loads and decrease the chance of possible failure from job site connections.

HG Clip


Features

  • Loads based on #10 screws
  • Pre-punched guide holes
  • Ledger tabs to hold header during installation
  • Designed for multiple stud sizes and jamb configurations
  • Replaces traditional labor intensive installation methods

thumbnail of HG

HG Submittal Download


Material Composition

  • ASTM A653/A653M
  • 43 mil: yield strength: 33 ksi
  • 68 mil: yield strength: 57 ksi
  • 43 mil: G60 hot dipped galvanized coating
  • 68 mil: G90 hot dipped galvanized coating
  • Material thickness = 43 mil
  • Material thickness = 68 mil

HG Clip

Allowable Loads

HG Screw Pattern
All screw pattern configurations depicted with jamb stud located on left hand side of clip.

Part No. Stud Properties F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 10 #10 Screws 12 #10 Screws
HG -43
(43 mil)		 33EQS 20 57 804 1206 1608 2010 2412
33 20 33 707 1060 1414 1767 2120
43EQS 18 57 1269 1904 2538 2980 2980
43 18 33 1052 1578 2104 2630 2980
54 16 50 1388 2082 2776 2980 2980
68 14 50 1388 2082 2776 2980 2980
97 12 50 1388 2082 2776 2980 2980
118 10 50 1388 2082 2776 2980 2980
Maximum Allowable Clip Capacity Max F3 = 2980 lbs
Part No. Stud Properties F3 Allowable Loads (lbs)
Mil Gauge Fy (ksi) 4 #10 Screws 6 #10 Screws 8 #10 Screws 10 #10 Screws 12 #10 Screws
HG-68
(68 mil)		 33EQS 20 57 804 1206 1608 2010 2412
33 20 33 707 1060 1414 1767 2120
43EQS 18 57 1269 1904 2538 3173 3808
43 18 33 1052 1578 2104 2630 3156
54 16 50 2136 3205 4273 5341 5375
68 14 50 3021 4531 5375 5375 5375
97 12 50 3170 4755 5375 5375 5375
118 10 50 3170 4755 5375 5375 5375
Maximum Allowable Clip Capacity Max F3 = 5375 lbs

Screw shear values are based on the SSMA Screw Table with the following notes:

  1. Allowable loads have not been increased for wind, seismic activity, or other factors.
  2. Screw spacing and edge distance shall not be less than 3 x d (d=nominal screw diameter).
  3. The allowable loads are based on the steel properties of the members being connected, per AISI Section E4.
  4. When connecting materials of different thicknesses or tensile strength (Fu), the lowest applicable values should be used.
  5. Attachment from the clip to the structural to be designed by others.
  6. Values include a 3.0 factor of safety.
  7. Applied loads may be multiplied by 0.75 for seismic or wind loading, per AISI Section A5.1.3
  8. Penetration of screws through joined materials should not be less than three exposed threads. Install and tighten screws in accordance with the screw manufacturer’s recommendations.

Quantity / Order Information

Model No. Left/Right
Handed		 Qty
/Bucket		 Lbs
/Bucket
HG-43 Universal 50 34
HG-68 Universal 30 32

Note: Secure plate “HG” is designed to accommodate all stud widths and flange heights and can be used on either side of the assembly.

The post HG – Secure Plate Header Gusset appeared first on SCAFCO Steel Stud Company.

]]>